JMR electronic Fortra 5251F6 Manual do Utilizador

I6 Infortrend 5251F615-bay Rackmount & Tower EnclosuresInstallation GuideOctober 22, 2003 • Revision APatent Pending

Thermal SpecificationsFORTRAenclosures have been designed to meet the air-flow/coolingrequirements for popular 7,200, 10,000 and 15,000 RPM disk dri

3-1FORTRA15-bay I6 Infortrend 5251F6 Installation Guide Rev AThis chapter covers Fibre Channel device installation for 15-bay rackmountand15-bay tow

Drive InstallationDevice mounting screws are included with the unit for device mounting. TheJMR part number for the #6-32" mounting screws is HD

4. Repeat steps 1 through 3 until all devices are installed, then move ontostep 5 to complete unit setup and installation.5. Configure ID and other op

4-1FORTRA15-bay I6 Infortrend 5251F6 Installation Guide Rev AThis chapter covers Fibre Channel device configuration and option settings. AllFibre C

Setting IDRotary switch settings only affect Slot 0 and all other slots are sequentiallyincreased by a value of one after that slot. The ID is set seq

ID ConflictWhen two devices share the same ID, a conflict occurs. This should not happenunless two or more enclosures are daisy chained together. If

External I/O ConnectionThe external I/O connections are located on both the personality card and thecontoller card. There are five SFP I/O connectors

CH 3 (Top)This is a standard (2Gb/s) SFP transceiver connector used to connect to a driveexpansion enclosure for Loop B side of drives. The 15 intern

This chapter covers all operations of the blowers for 15-bay units. Refer toChapter 1 for blower specifications. The blower is hot swappable and ca

iiFORTRA15-bay I6 Infortrend 5251F6 Installation Guide Rev ACopyrightCopyright 2003 by JMR Electronics, Inc. All Rights Reserved. No part of this

5-2FORTRA15-bay I6 Infortrend 5251F6 Installation Guide Rev AUser’s removing or installing a blower must be awarreof the blower access hole. Contact

6-1FORTRA15-bay I6 Infortrend 5251F6 Installation Guide Rev AThis chapter covers all operations of the power supplies. For operation, the ACcord (i

6-2FORTRA15-bay I6 Infortrend 5251F6 Installation Guide Rev ALow Power Mode (Standby Power)When both power supplies are turned off, the unit will sw

7-1FORTRA15-bay I6 Infortrend 5251F6 Installation Guide Rev AThis chapter covers the installation of the Rackmount enclosure into a standard19"

7-2FORTRA15-bay I6 Infortrend 5251F6 Installation Guide Rev ARail Mounting Kit Hardware• Ten #10-32 Screws• Four each #8-32 Screws/Washers/NutsSpare

2. Affix the extension bracket tothe rear of the unit using two#10-32 screws. There are 3holes in the extension bracketfor mounting. Depending on the

4. Slide the unit into the cabinet and secure it to the cabinet with a single#10-32 screw on each side.5. Snap the end cap over the screw on each side

8-1FORTRA15-bay I6 Infortrend 5251F6 Installation Guide Rev AFor bus management, the FORTRAFibre channel enclosures have a built-inSES processor d

9-1FORTRA15-bay I6 Infortrend 5251F6 Installation Guide Rev AThis model is designed to be used with up to two 5251F6 RAID bridge controllersfrom Inf

10-1FORTRA15-bay I6 Infortrend 5251F6 Installation Guide Rev AFor current information on this product, including updates to the manual andtechnical

iiiFORTRA15-bay I6 Infortrend 5251F6 Installation Guide Rev ATable of Contents1. Introduction2/4/6/8/10/12/15-bay Product Family Features . . . . .

A-1FORTRA15-bay I6 Infortrend 5251F6 Installation Guide Rev ADrive ManufacturersFujitsuInternet Address: www.fcpa.comHitachi Global Storage Technolo

ivFORTRA15-bay I6 Infortrend 5251F6 Installation Guide Rev AHost CH-0 and CH-1 (Top) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

The 15-bay FORTRAI6 Infortrend 5251F6 enclosures are designed to be usedwith a host system to provide a high-end RAID subsystem. The following is a

1-2FORTRA15-bay I4 Infortrend 5251F44 Installation Guide Rev AFORTRAproducts use advanced mid-plane technology developed by JMR,which allows power

1-3FORTRA15-bay I6 Infortrend 5251F6 Installation Guide Rev ABlowerQuantity: 4 (2 per cannister)Size: 97mm (3.82") eachAir Flow: 25.42CFM

2-1FORTRA15-bay I6 Infortrend 5251F6 Installation Guide Rev AThis chapter covers specification information for all FORTRAenclosures. Thefollowing

2-2FORTRA15-bay I6 Infortrend 5251F6 Installation Guide Rev AEnvironmental SpecificationsOperating Temperature: 5°C to 40°C (41°F to 104°F)Storage T